進口黃銅電磁閥(德國OLES奧萊斯閥門)
【進口黃銅電磁閥】詳細說明：
蒸汽電磁閥產品可廣泛應用于紡織、印染、化工、塑料、橡膠、制藥、食品、建材、機械、電器、表面處理等生產和科研部門以及浴室、食堂、空調等人們?nèi)粘Ｉ钤O(shè)施中。蒸汽電磁閥主要用于空氣、蒸汽、煤氣等氣體介質的控制；主要用于自來水、蒸餾水、冷凍鹽水、電鍍廢液等液體介質，同時也用于粘度小于4°E的油類。
Steam solenoid valve products can be widely used in textile, printing and dyeing, chemical industry, plastics, rubber, pharmaceuticals, food, building materials, machinery, electrical appliances, surface treatment and other production and scientific research departments, as well as bathroom, canteen, air conditioning and other people's daily life facilities. Steam solenoid valves are mainly used for controlling gas media such as air, steam and gas. They are mainly used for liquid media such as tap water, distilled water, refrigerated brine, electroplating waste liquor, and for oils with viscosity less than 4 degrees E.
【進口黃銅電磁閥】特點：
耐腐：主要部件閥塞，閥體等采用不銹鋼和鑄鋼制成，防腐性能良好。
耐熱：電磁、密封部分全部采用特種耐高溫電工材料和密封材料，并采用了有效的隔熱措施。
耐磨：選材合理，閥塞與閥體間巧妙地利用流體的潤滑作用，減少磨損。
耐冷凝：蒸汽管道的冷北水是影響蒸汽電磁閥動作的重要因素，本閥則不受冷凝水影響。
Corrosion resistance: The main components such as valve plug and valve body are made of stainless steel and cast steel, and the corrosion resistance is good.
Heat resistance: All the electromagnetic and sealing parts are made of special high temperature resistant electrical materials and sealing materials, and effective thermal insulation measures are adopted.
Wear resistance: reasonable material selection, skillful use of fluid lubrication between plug and valve body, reduce wear.
Condensation resistance: North water of steam pipeline is an important factor affecting the operation of steam solenoid valve, which is not affected by condensation water.
【進口黃銅電磁閥】安裝說明：
1、安裝前應參閱該產品的使用說明書，是否符合您的使用要求。
2、管路使用之前應沖洗干凈，介質不清潔的應安裝過濾器，以防止雜質妨礙電磁閥的正常工作。
3、電磁閥一般是單向工作的，不能反裝，閥上箭頭是管路流體的運動方向，必須保持*。
4、電磁閥安裝一般閥體水平，線圈垂直向上，有部分產品可以任意安裝，但在條件允許時垂直，以增長使用壽命。
5、電磁閥在結冰場所重新工作時應加熱處理，或設置保溫措施。
6、電磁線圈引出線（接插件）連接好后，應確認是否牢固，聯接電器元件觸點不應抖動，松動將引起電磁閥不工作。
7、連續要生產工作的電磁閥，采用旁路，便于檢修，不影響生產。
8、長時間停用后的電磁閥，應排清凝結物后方可使用；拆洗時各零件要按順序放好再恢復原狀裝好。
【進口黃銅電磁閥】?jī)?yōu)點：
黃銅電磁閥動作方式：直動式，分步直動式
先導膜片式 機械配套產品
無噪音，零泄漏
動作響應迅速，高頻率
